Rig pumper

"Whenever I’m motoring with the wind about 10 degrees off the starboard bow, the mast starts pumping so badly that it shakes the whole boat. The same thing happens at anchor. The mast is deck-stepped, and I’ve beefed up the compression post under the deck to make it rock solid. I’ve also checked the mast with a plumb bob and found that the column is straight but has a slight rake aft. All the
Author:
Updated:
Original:

"Whenever I’m motoring with the wind about 10 degrees off the starboard bow, the mast starts pumping so badly that it shakes the whole boat. The same thing happens at anchor. The mast is deck-stepped, and I’ve beefed up the compression post under the deck to make it rock solid. I’ve also checked the mast with a plumb bob and found that the column is straight but has a slight rake aft. All the rigging is tensioned evenly. I’d like to know why this pumping action occurs when the wind is blowing onto one side. A professional rigger told me he had no idea. Is there anything else I might do?"

-- Dan Smith, Fort Myers, Florida


Win Fowler replies: This problem is not uncommon, particularly with a single-spreader deck-stepped mast with just a single set of in-line lower shrouds. The best solution is to install forward and aft lower shrouds; usually this means installing additional chainplates and possibly reinforcing the hull. The tangs under the spreaders will also have to be modified.

To stop the pumping, try rigging a temporary babystay from a yoke at the spreader base down to the stemhead. Tensioning it when you are under power or at anchor should solve the problem. Be careful not to tension the stay so much that you pull the mast forward out of the column more than the distance of the mast’s diameter. Take the stay base back to the mast when you’re sailing; the mainsail should stabilize the mast and keep it from pumping. If this temporary stay works, you might think about adding a permanent stay.

I can only guess why the pumping occurs at one specific angle, but I suspect that the base of the mast is not bearing perfectly evenly on the step. A very small misalignment, just 1⁄64 inch or less, will be enough to affect the dynamic behavior of a deck-stepped mast. The problem might also be that the base of the mast is not perfectly square to the maststep. Or it could be a little of both. Unstep the mast to check the squareness of its base and see whether there is wear or corrosion on the step. When the step and the mast base are perfectly aligned with each other, the tendency to pump will be reduced; the more the base of the mast is supported by the step, the better. Of course, the step itself must not move.

Related

furlex2

Know-how: Installing an Electric Furler

Push-Button Reefing Boats have never been easier to sail, and yet, designers and builders still strive for that extra iota or two of convenience. A case in point is the growing acceptance of powered headsail furlers. Roller-furling headsails are ubiquitous not only on cruising ...read more

New-Lead

Know-how: Modify a Blackwater System

My dissatisfaction with the head and holding tank plumbing arrangement on our 1987 Sabre 38 had grown as we cruised the boat away from the comforts of a marina for longer periods of time. When we are tied up at a marina, the use of regular bathrooms generally trumps the ...read more

01-LEAD-Suzuki-55f19d31e297c

Choosing the Right Outboard

Two of the most indispensable items on board a cruising yacht are a dinghy and an outboard motor. At anchor or on a buoy, of course, they are your only means of getting ashore. They also have a thousand other uses. For example, they can allow you to motor across to friends’ ...read more

2019-giftGuide

2019 Holiday Gift Guide

Sailing America Rizzoli International Publications has released this striking portrait of American sailing by nautical photography legend Onne van der Wal just in time for the holidays. Featuring 200 stunning photographs spanning the length and breadth of the sailing scene—from ...read more

01-Sailing-La-Vagabonde,-Outremer-48

Cruising: the Vagabonde Life

Once upon a time conquering your dream of sailing off into the sunset was enough, but these days it seems like you have to be popular on social media too. Balancing the stresses of sailing around the world while keeping a successful—not to mention financially lucrative—social ...read more

191114

Video: 11th Hour Racing Arrives in Brazil

Team 11th Hour Racing finished in fourth place this past week among the 29 IMOCA 60s competing in the 4,335-mile doublehanded Transat Jacques Vabre race from Le Havre, France, to Salvador de Bahia, Brazil. Aboard were American Charlie Enright and French sailor Pascal Bidégorry, ...read more

Video--Edmond-de-Rothschild-Maxi-tri-Pitstop

Video: Edmond de Rothschild Maxi-tri Pitstop

. On Sunday, after having been first across the equator in the Brest Atlantiques race , Franck Cammas and Charles Caudrelier aboard the Ultime maxi-tri Maxi Edmond de Rothschild reported they’d be making a pitstop in Salvador de Bahia, in Brazil, after damaging one of their ...read more

T31A4577

Cruising the Eagle Class 53

Sailing at 19 knots in 15 knots of breeze is not an earth-shattering experience anymore. I was thinking about that on a perfect late summer day in Narragansett Bay while we were slicing along on the most technologically advanced cruising catamaran I’ve ever seen—the Eagle Class ...read more