Keel improvements - Sail Magazine

Keel improvements

Jabberwock, the BoatWorks project O’Day 25, was looking very scruffy around the underparts. The boat had been standing for so long that most of the paint had just fallen off the bottom, and the keel was looking particularly seedy. There was no way we could launch the boat with the keel in such bad condition. It was time for a makeover. A proper keel job done by a boatyard will cost
Author:
Publish date:

Jabberwock, the BoatWorks project O’Day 25, was looking very scruffy around the underparts. The boat had been standing for so long that most of the paint had just fallen off the bottom, and the keel was looking particularly seedy. There was no way we could launch the boat with the keel in such bad condition. It was time for a makeover. A proper keel job done by a boatyard will cost upward of $1,000, but we reckoned we could do it ourselves for a fraction of that. We were lucky in that the keel was lead; a cast-iron keel would have been much more labor-intensive.

If you want to get the last ounce of performance out of your boat, you may be able to buy a set of templates for your keel (try the builder, or www.computerkeels.com). These will ensure that your keel is perfectly symmetrical and fair on both sides. Enthusiastic racers may want to do this, but for the average cruising sailor, near enough is good enough. Even an imperfectly faired keel will improve your boatspeed.

typical_keel_age
orbital_sander_disk
project_keel_supplies
seal_joint_keel_hull
36_grit_sandpaper_keel
bare_metal_fiberglass
skin_hull_keel_joint
mat_hull_keel_joint
smooth_mat_work_resin

Related

Sun-Odyssey-490-Bertrand_DUQUENNE-aft

Boat Review: Jeanneau Sun Odyssey 490

True innovation in monohull sailboat design can be a bit elusive these days. That’s not to say that there are no more new ideas, but it does seem that many new tweaks and introductions are a bit incremental: let’s say evolutionary rather than revolutionary. Just when it seems ...read more

X3M-family

Gear: X3M Flight blocks

Block PartyThe elegance of these new X3M Flight blocks from Ubi Maior conceals the fact that they can handle loads of up to 15 tons. Designed to be used with a variety of textile loops, as fixed or snatch blocks, the X3M blocks have resin frames to carry the loops and anodized ...read more

03-BAVARIA-C34_Interior-2k_2

Ask Sail: The Right Cabin Sole Finish

Q: I am working on refinishing my cabin floorboards. I have brought them home and sanded the old finish off and would appreciate comments on using varnish or polyurethane for the sole.— Danny Love, Grand Rivers, KYDON CASEY REPLIES Polyurethane is the better choice for a cabin ...read more

shutterstock_peterisland

The Caribbean Charter Trade Rides Again

“The BVI is now a bit like it was 20 years ago,” Josie Tucci, vice president of sales and marketing for sister companies Sunsail and The Moorings, told me last December. “Instead of full bars, it may be a guy on the beach with a cooler and a barbeque, but the spirit of the place ...read more

Dragging01

Waterlines: Fear of Dragging

If you have a paranoid personality, anchoring out can be a validating experience. On the one hand, it seems rather simple. You amble up to the bow of your boat, drop a lump of metal overboard, let out some rode and secure it somehow. Then you stroll back to your cockpit and ...read more

TOTW_PromoSite

SAIL's Tip of the Week

Presented by Vetus-Maxwell.Got a tip? Send it to sailmail@sailmagazine.comTake it easy  Looks untidy, huh? Maybe it does, but I’ve hoisted a lot of mainsails over the years. A few go up easily. Many are a struggle. Sometimes it’s about turning blocks and nasty mast-tracks, but ...read more