Skip to main content

Boat Works: Re-bedding Ports

Rougher conditions can create leaks aboard wooden boats, especially

Rougher conditions can create leaks aboard wooden boats, especially

The old saw that the happiest day in a sailor’s life is the one on which they sell their boat is funny, of course, because of the fact that owning a boat can be both expensive and a lot of work. If you sail a boat hard, and especially if you’re in the habit of making ocean crossings, taking care of the rigging, sails, systems, engine and, of course, the hull and deck is not only crucial but ongoing. Let’s look at one of the most insidious maintenance issues: leaks.

Nothing eats away at a crew’s morale like a leaking boat, whether the water is coming in from overhead or below the waterline. Over time, there’s also nothing like leaks for eating away at a boat, too. As long as those leaks keep leaking, you’ve got a damp boat, which will turn into a rotten boat if you don’t do something.

Traditional wooden boats are, of course, at a greater risk than more modern vessels made out of fiberglass. But that doesn’t mean the latter can’t still have problems. Cored GRP boats, in particular, are notorious for losing structural integrity in their decks when leaks around fittings aren’t repaired. Similarly, metal boats can corrode, while cold-molded wooden boats constructed of wood veneers saturated in epoxy, like our 40ft Francis Kinney designed cutter Celeste, can rot out as well. The good news is that kept in good condition, Celeste is as comfortably dry as any other boat out there. However, keeping her that way means either not sailing her very hard—something my husband, Seth, and I are unwilling to do, since sailing across oceans is why we bought her in the first place—or being sure to re-bed her various fittings if and when they start leaking.

Sailed hard enough for long enough, all boats will flex in the highly dynamic environment of the open ocean. There is the force of the waves, for example, which is ever-changing. Sometimes you might be surging along with the swells. Other times you may find yourself punching into them. Still, other times the boat might have a corkscrewing motion as two different sets of swells come in from different directions, meeting to form confused, pyramid-like waves. There is also the constant pressure of the rigging, with the forces of the forestay and backstay effectively trying to fold the hull in half. Given all these constantly changing and often extreme pressures, it’s a wonder the seams and joints of all boats don’t leak all the time!

The deck prism was a source of one of the leaks (left); taped up prior to re-sealing (right,

The deck prism was a source of one of the leaks (left); taped up prior to re-sealing (right,

When Seth and I bought Celeste, we were astonished—and grateful—to discover how dry she was, and we continued to be astonished as she remained watertight over the course of five years exploring in the cool and rainy climate of Alaska. It was not until we sailed to the hot, arid climate of Mexico’s Sea of Cortez that problems started. Thanks to the fact Celeste is built of cold-molded wood, she did not develop any leaks in her hull or decking. However, the heat did begin to shrink the material around her various fittings: including her bronze portlights, the frame holding the center hatch, the deck prisms, the foot switch for the anchor windlass, the stanchion bases and the bow pulpit.

At first, we didn’t know we had a problem, and it’s really more a guess than anything else that the desert climate of Baja is what started it all since it would take another two and a half years in French Polynesia before any of Celeste’s incipient leaks became truly noticeable. Even then, none of the leaks that we had were much of a problem as we limited our sailing to a number of shorter passages around the islands. Then came the passage back home to Hawaii, during which it only took a few short days to realize just how bad things had become.

The trip consisted almost entirely of strong headwinds and steep seas, which caused a lot of flexing and strain on Celeste (see Close-hauled to Hawaii, SAIL September 2021). This in turn caused the boat’s many leaks to quickly became not only noticeable but quite unpleasant, prompting us to set straight to work trying to trace their origins. The source of the leak over the leeward bunk—the ideal leak for killing on-board happiness—quickly proved to be the deck prism. The water trickling from around the portlights was pretty obvious as well. The water dribbling along overhead remained a mystery until we finally traced it back to the center hatch frame. Try as we might, we were unable to accurately trace the many leaks originating from around a number of stanchions, the bow pulpit and windlass switch until after our arrival in Hawaii.

No big surprise, upon our arrival home tackling the many leaks we’d discovered was our top priority, and first on the list were those deck prisms. They had apparently last been bedded with 3M 5200, an extremely strong adhesive sealant that’s supposed to be permanent. This in turn makes it very difficult to remove anything it has been used to attach, to the point where when we pried out the prisms and their bronze frames, some of the teak and marine plywood of the surrounding deck came along with them. Given this experience, in our opinion 5200 is best used only when strength is your primary concern. If flexibility and a watertight seal for when the boat is flexing at sea is more of a priority than strength, better to go with something else.

Of course, strength in the sealant was not a big concern with the deck prisms: that’s provided mostly by the screws holding the frame. We, therefore, re-bedded the prisms with a combination of marine silicone and polyurethane sealant from Boat Life called LifeSeal. As a first step, we repaired the bits of the deck that had been damaged by the 5200 with West System epoxy and low-density filler. While waiting for it to cure, and before we could sand it smooth, we also scraped, scrubbed and sanded off all the old sealant from the prisms and frames. As a final step, we taped the prism and deck with painter’s tape, cleaned the surfaces with solvent and then used plenty of sealant to make sure both the joint and the screws would be watertight.

With the deck's prism taken care of, it was time to move on to the portlights, which had been bedded with an unknown but old and very sticky sealant. I doubt it was 5200 because they were so easy to remove. Once we’d taken out the screws, it just took a knife blade inserted in between the wood and the bronze to remove the bronze frames. No wood came away from the cabin. By contrast, removing the sealant from the bronze frames, the Lexan ports and the mahogany cabin was one of the toughest parts of the entire project. It took hours of elbow grease since neither turpentine nor acetone (which we only tried on the bronze) would defeat it.

Celeste’s portlights, re-bedded and ready for the next passage!

Celeste’s portlights, re-bedded and ready for the next passage!

As is the case with so many boat projects, prepping surfaces is the key to any good re-bedding job. If you don’t get all surfaces perfectly clean and ready, you are almost guaranteed to develop another leak. Once we’d cleaned up the frames, ports and cabin, we tackled a spot where the wood had started to rot away, sanding it back until we got to solid wood and then building it back up again with some more West System epoxy and low-density filler. Had the rotted area been any larger, we would have scarfed in a new piece of wood. Our cabin-sides, like the rest of the boat, are made of laminate, which means they don’t rot easily, and the rot takes a while to spread in the event it ever gets started. It also means using epoxy on them is perfectly acceptable.

Before putting the ports back in, we prepped everything with mineral spirits to make sure all surfaces were as clean as possible. As was the case with the deck prisms, strength was not a major consideration for the sealant, since once again, a combination of frames and screws would provide the necessary strength to hold the ports in place. Something we did want was a sealant that bonded well to metal and Lexan, and could also be removed easily when we inevitably need to bed the ports again, so we chose simple, clear silicone. As we were putting everything back together, we made sure to bed the Lexan ports themselves, the bronze frames and each screw. Water getting into the wood through a screw hole might not cause any noticeable leaks in the cabin, but could become a source of rot.

After that, it was time to move on to the stanchion bases and the bow pulpit, where we followed the same basic process of removing the requisite hardware; cleaning up the deck and the stainless steel bases; taping around the area to be sealed; wiping down everything with mineral spirits to ensure good adhesion; then bedding both the bases and screws with LifeSeal.

By contrast, the foot switch for the anchor windlass proved a slightly bigger project. We had ordered an entirely new switch, as the inner workings of the old one had become corroded beyond repair, and the new switch was slightly bigger than the one it was replacing. This, of course, makes for a much better scenario than receiving a fitting that is smaller than the hole in which it is to be installed. However, it still required a little ingenuity. Normally when you use a hole saw, the drill bit bites into the center of the area where you’re making the hole. But since we already a hole in the deck, there was nothing for the drill bit to bite into. We, therefore, found a piece of scrap wood we had in our extras bin, marked out the circle we’d have to cut for the new switch, drilled that out and then used it as a pattern for the actual hole we needed to cut in the deck. After that it was fairly straightforward to prep the surface, bed it with LifeSeal and attach the electrical connections on the underside to connect it to the anchor windlass itself.

Note that while the key to assuring a good seal is careful surface preparation, the key to a neatly finished final project is taping. Taping off the area where the sealant will go creates a professional end result. It allows you to avoid having to scrub off any sealant that somehow manages to find its way where you don’t want it and also makes it easier to remove any excess. We always use painter’s tape, which comes off easily and doesn’t mar the surface it’s been adhered to.

Keeping on top of leaks is essential for maintaining a boat in seaworthy condition. Not rushing the project, preparing the surfaces and using the best sealant for the job should result in a dry boat. This allows the boat to last longer, keeps her safer at sea and, of course, vastly improves crew morale. When Seth and I sailed Celeste on her next trip among the Hawaiian Islands, there were no leaks over any of the bunks, making the trip that much more pleasant for all! 

September 2022

Related

maintenance

Cruising: Old Sailors Never Die

“Old sailors never die, they just get a little dinghy.” It may be a hoary old joke, but one of my problems at age 79 is I can no longer get easily in and out of a little dinghy, and neither can my (several years younger than me) wife. For this, and various other reasons I will ...read more

01-LEAD-DSC_0953

The Mighty Compass

Here’s to the humble magnetic compass, without a doubt the sailor’s most reliable instrument onboard. It’s always there for you and with the rarest of exceptions, always operational. Yes, I love my chartplotter, autopilot, radar and AIS. They help me be a safer and more ...read more

02-En-route-Jost-Van-D

Chartering: Swan Song in the BVI

Joseph Conrad once wrote, “The sea never changes.” And while this may or not be true, something most definitely not open for debate is the fact we sailors, “wrapped in mystery,” as Conrad put it, are continually changing—whether we like it or not. I found myself thinking these ...read more

220307FP51_1JML0332

Boat Review: Fountaine-Pajot Aura 51

If you can sell more than 150 catamarans off-plan before the resin has even hit the fiberglass, you must be doing something right. Despite costing around $1.1 million once fitted out and on the water, Fountaine-Pajot’s new 51 has done just that. The French yard has been at it ...read more

00LEAD-IMG-9035

Ready to Fly a New Sail

It’s a typical humid, southern Chesapeake Bay summer day when I show up on the doorstep of Latell & Ailsworth Sailmakers in the one-stoplight, one-lane-roadway, rural tidewater town of Deltaville, Virginia. I’m late getting here to work on a new jib for my 29-foot, Bill ...read more

m5702_RACE-AREA-6

Dates for the 2024 America’s Cup Announced

Ever since making the controversial decision to hold the next America’s Cup in Barcelona, Spain, instead of in home waters, Defender Emirates Team New Zealand has been hard at work organizing logistics for the event.  The Racing Area for the Challenger Selection Series and the ...read more

00LEAD

A Force for Change: Captain Liz Gillooly

I first heard about Capt. Liz Gillooly in 2016 from my cousin while working three jobs in our shared hometown on the North Fork of Long Island and living with my parents to save money for a boat. But despite being the same age and growing up only 13 miles apart, Liz and I never ...read more

291726157_3222349914654950_8713674249134934221_n-2-1024x684

Sailing in the Growth Zone

The Goal This year, I’ve had a specific goal to be a better sailor. Some people have laughed and said, “Why do you need to be a better sailor? This was my 22nd year racing on the same boat, with the same crew. I like to win and want to make sure we stay at the top of the fleet. ...read more